plastic platform 0.3max. f d0.5 b0.2 a0.2 a0.2 c0.2 0.5max. e h h positive negative plastic platform 0.3max. f d0.5 b0.2 a0.2 a0.2 c0.2 0.5max. e positive negative u 1 w 2 h 3 1 4 a 5 1 6 0 7 1 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration package code capacitance tolerance (20%) rated capacitance ( 100 m f ) rated voltage ( 10v ) series name type l0.3 l0.5 8 6.2 f d l a b c e 3.3 8.3 8.3 2.3 8 10 2.9 8.3 8.3 3.1 10 10 3.2 10.3 10.3 4.5 l 6.2 10 10 h 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 (mm) trade mark n2 100v wh n2 100a wh voltage (a:10v) capacitance lot no. capacitance lot no. series trade mark voltage (v:35v) series wh series chip type, high reliability high temperature (260 ?) reflow corresponding with 260 ? peak reflow soldering recomended reflow condition : 260? peak 5 sec. 230? over 60 sec. 2 times ( 8 6.2, 10 10 : 1 time) chip type high temperature range, for +125 ? use. applicable to automatic mounting machine using carrier tape. adapted to the rohs directive (2002/95/ec). chip type ( 8 6.2) ( 8 10, 10 10) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tan stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item 40 ~ +125? 10 ~ 50v 10 ~ 330 f 20% at 120hz, 20? after 1 minute's application of rated voltage, leakage current is not more than 0.03cv or 4( a) , whichever is greater. black print on the case top. measurement frequency : 120hz after 1000 hours' application of rated voltage at 125?, capacitors meet the characteristic requirements listed at right. after storing the capacitors under no load at 125? for 1000 hours, and after performing voltage treatment based on jis c 5101- 4 clause 4.1 at 20?, they will meet the specified value for endurance characteristics listed above. z 40? / z+20? rated voltage (v) impedance ratio zt / z20 (max.) 10 12 16 8 25 6 35 4 50 4 type numbering system (example : 10v 100 f) the capacitors shall be kept on the hot plate maintained at 250? for 30 seconds. after removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right . rated voltage (v) tan (max.) 10 0.32 16 0.24 25 0.21 35 0.18 50 0.18 measurement frequency : 120hz, temperature : 20? capacitance change leakage current tan within 10% of initial value initial specified value or less initial specified value or less capacitance change leakage current tan within 30% of initial value initial specified value or less 300% or less of intial specified value wh ub voltage v 1016253550 code a c e v h high temperature reflow dimension table in next page. aluminum electrolytic capacitors cat.8100v
aluminum electrolytic capacitors frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz~ 0.70 1.00 1.17 1.36 1.50 rated ripple (marms) at 125 c 120hz dimensions 10 22 33 47 100 220 330 100 220 330 470 101 221 331 8 6.2 8 10 10 10 8 10 10 10 8 6.2 8 10 10 10 8 6.2 8 10 10 10 8 6.2 8 6.2 8 10 10 10 58 90 112 66 102 48 74 116 44 52 80 24 38 46 58 1a 1c 1e 1v 1h 10 16 25 35 50 v code cap.(f) rated ripple wh series taping specifications are given in page 24. recommended land size, soldering by reflow are given in page 25, 26. please refer to page 3 for the minimum order quantity. case size d l (mm) cat.8100v
|
